Tub Grinders on GrinderCrusherScreen: Diamond Z, Duratech, Morbark, Olathe, Toro, Vermeer, WHO, and more

TUB GRINDERS

1991 Diamond Z 1663

$169,000

Stock# M121903-1

Engine: 700HP Electric
Approx Hrs on Frame: 3500
Approx Hrs on Engine: 3500
F.O.B.: West Coast USA - DB

Notes:
Skid Mounted
-16ft tub, quick change hammers, hydraulic tub tilt
-63" x 30" Hammer Mill 
-700hp electric motor for rotor (2,300/4160v)
- (2) remote electric power packs (480v) for aux hydraulics (tub rotation, 

conveyor etc)
-4160v and 480 volt switch gear
-Wireless remote control for start and stop, spare parts as photographed 
-Box was rebuilt and quick change hammers were installed and balanced in 2007
-Primary conveyor approx 30ft, additional 38ft conveyor available (no belt)
Approx 3,500 hrs use, this grinder has been well maintained and installed 

only at 1 facility
Recent cleaning and paint

Main Motor Data:
 -700hp
-2,300/4160v 
-60hz. 
-SF=1.0
-159/88 amps
-1183 rpm 
-Design B 
-Code G
 
There are 5 screens not counting what is currently in the machine, some have 

some signs of use others are unused, below are the hole sizes.
 
-4" x 3.75"
-9" x 8"
-5.5" x 3.75"
-6" x 4"
-8" x 9"
 
 
This machine is in nice shape, has not been abused and was under a good 

preventative maintenance program.   The box as rebuilt about 500hrs ago and 

the rotor was updated to the quick change hammers. The only main issue I see 

is with the 2 main control cabinets which have some rust on the bottom of the 

enclosures from constantly being in the path of the water mist drainage 

system used to keep the dust down for the grinder.  The rust is isolated to 

the steel enclosure bases and the internal components all look good and are 

mounted above the steel floor.

GCS Green Machine

$219,000

Stock# H110208-1

Engine: 85hp Diesel
Approx Hrs on Frame: 0
Approx Hrs on Engine:0
F.O.B.: South East, USA - HB

Notes:
            
10 Yard Hopper   (6’-10” wide x 20’-0 Long)                                            
54” wide x 16’ variable speed belt feeder                                            
48” wide x 90’-0 long discharge conveyor (makes 47’-0 tall piles, 42’ from center of pile to tires)                                           
Conveys up to 500 – 800 yph                                           
85 HP Diesel Engine (CAT / Cummins / John Deere                                           
89 Gallon Fuel Tank                                           
150 Gallon Hydraulic Tank                                           
Remote Control:  Power Radial, Raise & Lower of discharge conveyor, emergency stop
Weight: Approx. 55,000 lbs.
Transport width:  12' - 4" wide (must remove swivel wheels)

GCS Waste Wizard 1200 Density Separator

Stock# H120705-3

$189,000

Engine: Electric
Approx Hrs on Frame: 0
Approx Hrs on Engine: 0
F.O.B.: Mid Atlantic USA - OZ

Notes: The GCS waste wizard uses a unique system to separate mixed debris into sorted wood, aggregate, plastic, silt and more. It uses shaker screen, air separator, and water separation to organize a pile of leftovers into usable product. The 3 stage process includes: Shaker screening to sort the fines, air separation with variable air flow to pull light materials, and water separation to separate heavy materials from lighter materials.
The GCS Waste Wizard 1200 which can take raw materials 12 inch minus and has a low water consumption of 1.6 gallon per minute
Production rate;
If 70-80% Rock, approx. 80 tons per hour
If 1-10% Rock, approx. 25-30 tons per hour

GCS Waste Wizard 1000 Density Separator

Stock# H120705-2

$159,000

Engine: Electric
Approx Hrs on Frame: 0
Approx Hrs on Engine: 0
F.O.B.: Mid Atlantic USA - OZ

Notes: The GCS waste wizard uses a unique system to separate mixed debris into sorted wood, aggregate, plastic, silt and more. It uses shaker screen, air separator, and water separation to organize a pile of leftovers into usable product. The 3 stage process includes: Shaker screening to sort the fines, air separation with variable air flow to pull light materials, and water separation to separate heavy materials from lighter materials.
The GCS Waste Wizard 1000 which takes 7 inch minus raw material and has a low water consumption of 1 gallon per minute
Production rate;
If 70-80% Rock, approx. 70 tons per hour
If 1-10% Rock, approx. 20-25 tons per hour

Many brand of USED tub grinders including Diamond Z, Duratech, Haybuster, Olathe, Vermeer, and a large selection of Morbark tub grinders

TORO

MORBARK

HAYBUSTER

GCS

DURATECH

DIAMOND Z

1996 Toro Pro Grind 5000

$104,000

Engine: 650+HP
Approx Hrs on Frame: 4000
Approx Hrs on Engine: 4000 

Notes: 
New Mill shaft & main bearings Fall 2011
New Rear Driveline Fall 2011
Rebuilt fluid Coupler Spring 2012
Rebuilt Clutch & Pilot Bearing Summer 2012
New Tub Drive Gear Box Spring 2012
New Tub Drive Sprockets & Chain Nov. 2012
1 New Auger, 2 90% augers Nov. 2012
New Auger Drive Sprockets & Chain Nov. 2012
New Auger Bearings Nov. 2012
New Hydraulic Drive Motors / Augers Nov. 2012
Rebuilt Pump Drive Gear box Fall 2011
Rebuilt Hydrostatic Pump Oct. 2011
Rebuilt front driveline Aug. 2012
Balanced Mill, Fan, Rear & Sept. 2012
Front Drivelines
Rack Run by Cummins Northwest Nov. 2012
New Conveyor Belt Vulcanized Fall 2011
Repack Hydraulic cylinders Nov. 2012
New conveyor Bearings top & bottom Nov. 2012
Single axle Dolly to move onsite
Oil samples taken on all oil changes
Extra screens, hammers and misc parts
Grinder in EXCELLENT condition ready to work.

Stock #M122011-L1

VERMEER

WHO

OLATHE

* Click a brand name above to see what models we have available *

1992 Diamond Z 1463

$198,000

Stock# MM131405-3

Engine: 750HP Cat 3412
Approx Hrs on Frame: 
Approx Hrs on Engine: 2500
F.O.B.: West Coast USA - DB

Notes:
Grinder Equipped With:
1.   14 foot remote controlled tub.
2.   Cross belt magnet.
3.   Rod puller.
4.   Articulating secondary conveyor.
5.   Fixed hammers on 4-rod mill.

Also Includes:                                                               
1.   Tandem axle field dolly                                                  

2.   New motherboard for tub computer (in the box)                
3.   New remote for remote tub control and engine power during operation (in the box)                   
4.   Original service manual                                      
5.   Field remote for remote control of tub and engine power during operation                                             

                              
History:
In 2006, the engine, a Caterpillar 3412, was overhauled “in-frame.”  The injectors and injector pumps were also rebuilt and/or replaced.  The engine currently has less than 2,600 hours since overhaul. During the down time for engine maintenance, the mill was rebuilt and balanced.  The main drive clutch was also rebuilt.  In preparation for sale further work was done on the clutch, which included the replacement of all carrier and throw-out bearings. After it was sold last in late 2009, the machine was used to grind orchard removal through June of 2010.  The machine has been idle since June 6, 2010, and has been in the process of being inspected, rebuilt and/or reconditioned

**Detailed service notes available upon request**